TITLE 32 ELECTRONIC MEASUREMENT EQUIPMENT MECHANIC (MI SMO - CSMS)

TITLE 32 ELECTRONIC MEASUREMENT EQUIPMENT MECHANIC (MI SMO - CSMS)

Department: Department of the Army

Location(s): Lansing, Michigan

Salary Range: $37.62 - $43.86 Per Hour

Job Summary: THIS IS AN ARMY NATIONAL GUARD TITLE 32 EXCEPTED SERVICE POSITION. This National Guard position is for a TITLE 32 ELECTRONIC MEASUREMENT EQUIPMENT MECHANIC (MI SMO - CSMS), Position Description Number NGD1201000 and is part of the MI CSMS, Michigan Army National Guard.

Major Duties:

• ***THIS IS A TITLE 32 NATIONAL GUARD POSITION THAT REQUIRES MILITARY MEMBERSHIP*** This position is located in the Joint Forces Headquarters-State, Logistics Directorate (J-4), Surface Maintenance Facility. The primary purpose of this position is to perform calibration, diagnostics repair, and certification of electronic, mechanical, and radiation Test Measurement and Diagnostic Equipment (TMDE). Calibrates and repairs TMDE within support capability and authority including various levels of calibration as designated in technical bulletins, manuals, etc. Performs functional electronic, physical, and radioactive testing involving interpretation and analysis of measurement data, in accordance with cyclic inspection requirements. Sets up system test sets and various types of test equipment such as frequency meters, standing wave ratio meters, radio frequency (RF) power meters, function/ arbitrary waveform generator, distortion analyzers, time frequency work stations, oscillators, voltmeters, electronic counters, oscilloscopes, attenuators, decade resistors and capacitors, signal generators, stroboscope, tachometers, pneumatic and hydraulic pressure standards and other physical and electronic tests. Diagnoses equipment, makes repairs, and replaces defective parts/components such as integrated circuits, printed circuit boards, electronic condition coils, radiation detector boards/circuits, crystals, transistors, tubes, transformers, condensers, diodes, relays potentiometers, and related components. Following repair, tests by applying signals in known amplitude and wave shape into oscilloscopes to observe wave pattern. Isolates faults by taking measurements and comparisons in voltage, amperage, ohms, henries, power factor, watts, temperature, humidity, microns, foot-pounds, decibels, sensitivity, noise, stability, Voltage Standard Wave Ratio (VSWR), impedance, phase, absolute pressure, time intervals, displacement, flow rate, etc., to determine performance of equipment. Determines purpose in operation characteristics of each major section. Refers to technical manuals and manufactures specifications to obtain information on operation characteristics of circuit components such as integrated circuits, microprocessors, decoders, latching networks, notch filters, logics, controllers, programmable gain amplifiers, digital displays, transistors, tubes, transformers, coils, relays, motors, and similar devices. Disassembles, cleans and inspects parts such as printed circuit boards, resistors, capacitors, integrated circuits, relays, chambers, cables, and wiring for evidence or wear or malfunction. Completes necessary Army Maintenance Management System (TAMMS), calibration, radiation reports and other records and forms on work completed. Ensures maximum number of weapons systems are operationally ready. Follows appropriate safety procedures, with special care being exercised while calibrating high voltage, radio frequency, radioactive sources and high-pressure instruments and gages. Performs and interprets wipe tests on radiation sources for possibility of radiation hazards. Familiar with and abides by all Federal and State regulations concerning handling, transportation and disposal of radioactive waste or devices. The above duty description doesn't contain all details of the official position description.

Qualifications: In your resume you will need to address the general and specialized experience listed below. Please use as much detail as needed, giving dates (months and years) of the experience, position title and how the experience was gained. This information is needed to determine if you are qualified for the position. Military Grades: E1-WO4 SPECIALIZED EXPERIENCE: Experience or training with basic application of operating principles such as the production and utilization of oscillations over a broad range of frequencies; signal and waveform behavior, distortion, and amplification; pulse, trigger, and synchronization techniques; digital/analog processing and data conversion techniques; and a variety of display and indication methods. Experience in tracing signals and voltage paths, and skilled in the analysis of waveform characteristics such as timing, duration, frequency, and phasing. Originates test set-ups to isolate malfunctions and check performance characteristics of special or unique test panels or mockups. Experience in interpreting and applying a variety of technical electronic information such as schematic symbols, mathematical expressions and formulas, calibration procedures, and other reference materials. Experience in applying established techniques and methods of repair, testing, alignment, and calibration of equipment, which serves as test equipment or precision measurement standards. Experience in utilizing electronic circuits to measure electronic or electrical quantities to determine the performance characteristics and accuracy of other instruments and equipment.

How to Apply: To apply for this position, you must complete the online application/Occupational Questionnaire and submit the documentation specified in the Required Documents section below. To view the Occupational Questionnaire, click the following link: https://apply.usastaffing.gov/ViewQuestionnaire/12904492 A complete application package must be submitted by 11:59 PM (EST) on the closing date of the announcement to receive consideration. To begin, click Apply to access the online application. You will need to be logged into your USAJOBS account to apply. If you do not have a USAJOBS account, you will need to create one before beginning the application. Follow the prompts to select your resume and/or other supporting documents to be included with your application package. You will have the opportunity to upload additional documents to include in your application before it is submitted. Your uploaded documents may take several hours to clear the virus scan process. After acknowledging you have reviewed your application package, complete the Include Personal Information section as you deem appropriate and click to continue with the application process. You will be taken to the online application which you must complete in order to apply for the position. Complete the online application, verify the required documentation is included with your application package, and submit the application. To verify the status of your application, log into your USAJOBS account (https://my.usajobs.gov/Account/Login), all of your applications will appear on the Welcome screen. The Application Status will appear along with the date your application was last updated. For information on what each Application Status means, visit: https://www.usajobs.gov/Help/how-to/application/status/.

Application Deadline: 2026-03-27