ELECTRONIC MEASUREMENT EQUIPMENT MECHANIC

ELECTRONIC MEASUREMENT EQUIPMENT MECHANIC

Department: Department of the Air Force

Location(s): Otis ANG Base, Massachusetts

Salary Range: $42.29 - $49.32 Per Hour

Job Summary: THIS IS A NATIONAL GUARD TITLE 5 EXCEPTED SERVICE POSITION. This National Guard position is for a ELECTRONIC MEASUREMENT EQUIPMENT MECHANIC, Position Description Number PDT5791000 and is part of the MA ANG 102nd IW, National Guard. This is a Non-Bargaining Unit position. The unit point of contact and contact phone for this position is: Mr. Todd Morey at email todd.morey@us.af.mil. Selected applicant MAY BE eligible for a recruitment incentive not to exceed $20,000.

Major Duties:

• 1. Installs, tests, repairs, overhauls, fabricates or modifies, calibrates, troubleshoots and certifies highly complex electronic systems components or subassemblies. Installs and tests highly complex electronics equipment. Performs functional tests to locate equipment malfunctions in accordance with accepted trade practices to minimize equipment downtime. Diagnoses malfunctions of systems by thoroughly analyzing operating trends and ensuring repairs are accomplished. Independently troubleshoots highly complex electronic equipment to accurately determine the nature of the problem and the extent of repair required. Troubleshoots and tests complete electronic systems by following prescribed procedures to accurately identify improper operating parameters and defective parts, and in monitoring system operation and identifying improper operating indications. Independently determines work methods and test equipment to use on routine assignments compatible with specific technical instructions and within established timeframes. Calibrates and repairs complex electronic equipment ensuring the equipment is aligned to maximize operating potential and minimize downtime. Certifies completed work and prepares all necessary paperwork required to document maintenance actions taken. May provide advice and/or technical assistance to supported organizations and lower graded workers.(60%) 2. Sets up Test Measurement and Diagnostic Equipment (TMDE) and uses this equipment to ensure operational accuracy by performing intricate and complex laboratory and/or on site calibrations and repairs of electronic systems. Uses electronic measuring equipment ranging in complexity from multimeters to complex software-controlled automatic test equipment. Included are items such as special test panels, test sets, and consoles (consisting of analog or digital computers, digital multimeters, oscilloscopes, frequency/time/phase standards, frequency counters, spectrum analyzers, digital or cathode ray tube display devices, and attenuation and power measuring devices); light, radiation, and infrared measuring devices; regulated power supplies; data display units; pulse, sweep, marker and function generators; and other special purpose test panels/equipment used in conjunction with the repair, test and troubleshooting of assigned integrated systems. Sets up and uses dimensional measuring devices involved in linear, optical, force, mass, and pressure measurements using such items as but not limited to gage blocks, micrometers, calipers, sineplates, analog or digital electronic height gages, analytical balances, hydraulic calibration presses, autocollimators, theodolites, pentaprisms, air data computers, and flow measuring standards.(20%) 3. Uses and maintains tools and equipment. Uses trade tools such as wire strippers, drills, files, dremel tools, soldering irons, and microsoldering units to remove and replace parts. Uses various precision measurement standards and instruments such as generators, oscilloscopes, meters, and analyzers to perform inspections, functional testing, and calibration of TMDE.(10%) 4. Maintains records and documents actions. Prepares all certification paperwork required and documents work assignments using PMEL Automated Maintenance System (PAMS) computer.(5%) 5. Utilizes safety practices and procedures following established safety rules and regulations and maintains a safe and clean work environment. Uses and assures proper fit and placement of required safety equipment and clothing. Performs clean-up duties such as cleaning equipment, sweeping, and returning of equipment to proper locations when not in use. Maintains awareness of lab safety procedures and identifies any observed unsafe practices and/or procedures.(5%) Performs other duties as assigned.

Qualifications: AREA OF CONSIDERATION: Nationwide - Open to all US Citizens GENERAL EXPERIENCE: Must have experience or training which demonstrates a working knowledge of electronic principles involved in the generation and measurement of such elements as voltage, current, impedance, capacitance, frequency, and inductance. Experience in the use of various precision measurement instruments and standards. SPECIALIZED EXPERIENCE: Must have at least 18 months experience or training with basic application of operating principles such as the production and utilization of oscillations over a broad range of frequencies; signal and waveform behavior, distortion, and amplification; pulse, trigger, and synchronization techniques; digital/analog processing and data conversion techniques; and a variety of display and indication methods. Experience in tracing signals and voltage paths, and skilled in the analysis of waveform characteristics such as timing, duration, frequency, and phasing. Originates test set-ups to isolate malfunctions and check performance characteristics of special or unique test panels or mockups. Experience in interpreting and applying a variety of technical electronic information such as schematic symbols, mathematical expressions and formulas, calibration procedures, and other reference materials. Experience in applying established techniques and methods of repair, testing, alignment, and calibration of equipment, which serves as test equipment or precision measurement standards. Experience in utilizing electronic circuits to measure electronic or electrical quantities to determine the performance characteristics and accuracy of other instruments and equipment. PART-TIME OR UNPAID EXPERIENCE: Credit will be given for appropriate unpaid and or part-time work. You must clearly identify the duties and responsibilities in each position held and the total number of months/years. VOLUNTEER WORK EXPERIENCE: Refers to paid and unpaid experience, including volunteer work done through National Service Programs (i.e., Peace Corps, AmeriCorps) and other organizations (e.g., professional; philanthropic; religious; spiritual; community; student and social). Volunteer work helps build critical competencies, knowledge and skills that can provide valuable training and experience that translates directly to paid employment. You will receive credit for all qualifying experience, including volunteer experience.

How to Apply: To apply for this position, you must complete the online application/Occupational Questionnaire and submit the documentation specified in the Required Documents section below. To view the Occupational Questionnaire, click the following link: https://apply.usastaffing.gov/ViewQuestionnaire/12941070 A complete application package must be submitted by 11:59 PM (EST) on the closing date of the announcement to receive consideration. To begin, click Apply to access the online application. You will need to be logged into your USAJOBS account to apply. If you do not have a USAJOBS account, you will need to create one before beginning the application. Follow the prompts to select your resume and/or other supporting documents to be included with your application package. IMPORTANT: Your resume cannot exceed 2 pages. You will have the opportunity to upload additional documents to include in your application before it is submitted. Your uploaded documents may take several hours to clear the virus scan process. After acknowledging you have reviewed your application package, complete the Include Personal Information section as you deem appropriate and click to continue with the application process. You will be taken to the online application which you must complete in order to apply for the position. Complete the online application, verify the required documentation is included with your application package, and submit the application. To verify the status of your application, log into your USAJOBS account (https://my.usajobs.gov/Account/Login), all of your applications will appear on the Welcome screen. The Application Status will appear along with the date your application was last updated. For information on what each Application Status means, visit: https://www.usajobs.gov/Help/how-to/application/status/.

Application Deadline: 2026-05-21